Alfred's spAcE

2010.01.19

wd盒子后续

Filed under: Computers and Internet — Alfred Yang @ 13:03
smartctl –all /dev/sda4
smartctl version 5.38 [armv5tejl-unknown-linux-gnu] Copyright (C) 2002-8 Bruce Allen

=== START OF INFORMATION SECTION ===
Model Family:     SAMSUNG SpinPoint P120 series
Device Model:     SAMSUNG SP2004C
Serial Number:    S07GJ1MYC02774
Firmware Version: VM100-33
User Capacity:    200,048,565,760 bytes
Device is:        In smartctl database [for details use: -P show]
ATA Version is:   7
ATA Standard is:  ATA/ATAPI-7 T13 1532D revision 4a
Local Time is:    Tue Jan 19 04:35:39 2010 UTC

==> WARNING: May need -F samsung3 enabled; see manual for details.

SMART support is: Available – device has SMART capability.
SMART support is: Enabled

=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: FAILED!
Drive failure expected in less than 24 hours. SAVE ALL DATA.
See vendor-specific Attribute list for failed Attributes.

General SMART Values:
Offline data collection status:  (0x82) Offline data collection activity
                                        was completed without error.
                                        Auto Offline Data Collection: Enabled.
Self-test execution status:      (   0) The previous self-test routine completed
                                        without error or no self-test has ever
                                        been run.
Total time to complete Offline
data collection:                 (4778) seconds.
Offline data collection
capabilities:                    (0x5b) SMART execute Offline immediate.
                                        Auto Offline data collection on/off support.
                                        Suspend Offline collection upon new
                                        command.
                                        Offline surface scan supported.
                                        Self-test supported.
                                        No Conveyance Self-test supported.
                                        Selective Self-test supported.
SMART capabilities:            (0x0003) Saves SMART data before entering
                                        power-saving mode.
                                        Supports SMART auto save timer.
Error logging capability:        (0x01) Error logging supported.
                                        General Purpose Logging supported.
Short self-test routine
recommended polling time:        (   1) minutes.
Extended self-test routine
recommended polling time:        (  79) minutes.

SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME          FLAG     VALUE WORST THRESH TYPE      UPDATED  WHEN_FAILED RAW_VALUE
  1 Raw_Read_Error_Rate     0x000f   100   085   051    Pre-fail  Always       –       5
  3 Spin_Up_Time            0x0007   100   100   025    Pre-fail  Always       –       5760
  4 Start_Stop_Count        0x0032   100   100   000    Old_age   Always       –       586
  5 Reallocated_Sector_Ct   0x0033   001   001   010    Pre-fail  Always   FAILING_NOW 5356
  7 Seek_Error_Rate         0x000f   253   253   051    Pre-fail  Always       –       0
  8 Seek_Time_Performance   0x0025   253   253   015    Pre-fail  Offline      –       0
  9 Power_On_Hours          0x0032   100   100   000    Old_age   Always       –       13336
 10 Spin_Retry_Count        0x0033   253   253   051    Pre-fail  Always       –       0
 11 Calibration_Retry_Count 0x0012   253   002   000    Old_age   Always       –       0
 12 Power_Cycle_Count       0x0032   100   100   000    Old_age   Always       –       570
190 Airflow_Temperature_Cel 0x0022   118   082   000    Old_age   Always       –       40
194 Temperature_Celsius     0x0022   118   082   000    Old_age   Always       –       40
195 Hardware_ECC_Recovered  0x001a   100   100   000    Old_age   Always       –       942941
196 Reallocated_Event_Count 0x0032   001   001   000    Old_age   Always       –       5356
197 Current_Pending_Sector  0x0012   094   090   000    Old_age   Always       –       62
198 Offline_Uncorrectable   0x0030   100   100   000    Old_age   Offline      –       1
199 UDMA_CRC_Error_Count    0x003e   200   200   000    Old_age   Always       –       0
200 Multi_Zone_Error_Rate   0x000a   100   100   000    Old_age   Always       –       0
201 Soft_Read_Error_Rate    0x000a   253   099   000    Old_age   Always       –       0
202 TA_Increase_Count       0x0032   253   253   000    Old_age   Always       –       0

SMART Error Log Version: 1
ATA Error Count: 280 (device log contains only the most recent five errors)
        CR = Command Register [HEX]
        FR = Features Register [HEX]
        SC = Sector Count Register [HEX]
        SN = Sector Number Register [HEX]
        CL = Cylinder Low Register [HEX]
        CH = Cylinder High Register [HEX]
        DH = Device/Head Register [HEX]
        DC = Device Command Register [HEX]
        ER = Error register [HEX]
        ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.

Error 280 occurred at disk power-on lifetime: 5410 hours (225 days + 10 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER ST SC SN CL CH DH
  — — — — — — —
  40 51 08 f8 3e 5e 40  Error: UNC 8 sectors at LBA = 0x005e3ef8 = 6176504

  Commands leading to the command that caused the error were:
  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name
  — — — — — — — —  —————-  ——————–
  c8 03 08 f8 3e 5e 40 00      00:01:00.875  READ DMA
  ef 03 46 00 00 00 00 00      00:01:00.813  SET FEATURES [Set transfer mode]
  ef 03 0c 00 00 00 00 00      00:01:00.813  SET FEATURES [Set transfer mode]
  ef 03 00 00 00 00 00 00      00:01:00.813  SET FEATURES [Set transfer mode]
  ec 00 00 00 00 00 00 00      00:01:00.813  IDENTIFY DEVICE

Error 279 occurred at disk power-on lifetime: 5410 hours (225 days + 10 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER ST SC SN CL CH DH
  — — — — — — —
  40 51 08 f8 3e 5e 40  Error: UNC 8 sectors at LBA = 0x005e3ef8 = 6176504

  Commands leading to the command that caused the error were:
  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name
  — — — — — — — —  —————-  ——————–
  c8 03 08 f8 3e 5e 40 00      00:00:57.750  READ DMA
  ef 03 46 00 00 00 00 00      00:00:57.688  SET FEATURES [Set transfer mode]
  ef 03 0c 00 00 00 00 00      00:00:57.688  SET FEATURES [Set transfer mode]
  ef 03 00 00 00 00 00 00      00:00:57.688  SET FEATURES [Set transfer mode]
  ec 00 00 00 00 00 00 00      00:00:57.688  IDENTIFY DEVICE

Error 278 occurred at disk power-on lifetime: 5410 hours (225 days + 10 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER ST SC SN CL CH DH
  — — — — — — —
  40 51 08 f8 3e 5e 40  Error: UNC 8 sectors at LBA = 0x005e3ef8 = 6176504

  Commands leading to the command that caused the error were:
  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name
  — — — — — — — —  —————-  ——————–
  c8 03 08 f8 3e 5e 40 00      00:00:54.625  READ DMA
  ef 03 46 00 00 00 00 00      00:00:54.625  SET FEATURES [Set transfer mode]
  ef 03 0c 00 00 00 00 00      00:00:54.563  SET FEATURES [Set transfer mode]
  ef 03 00 00 00 00 00 00      00:00:54.563  SET FEATURES [Set transfer mode]
  ec 00 00 00 00 00 00 00      00:00:54.563  IDENTIFY DEVICE

Error 277 occurred at disk power-on lifetime: 5410 hours (225 days + 10 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER ST SC SN CL CH DH
  — — — — — — —
  40 51 08 f8 3e 5e 40  Error: UNC 8 sectors at LBA = 0x005e3ef8 = 6176504

  Commands leading to the command that caused the error were:
  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name
  — — — — — — — —  —————-  ——————–
  c8 00 08 f8 3e 5e 40 00      00:00:51.500  READ DMA
  c8 00 08 f0 3e 5e 40 00      00:00:51.500  READ DMA
  c8 00 08 60 0e a5 4b 00      00:00:51.438  READ DMA
  c8 00 08 00 3f 60 40 00      00:00:51.438  READ DMA
  c8 00 08 00 3f 00 40 00      00:00:51.438  READ DMA

Error 276 occurred at disk power-on lifetime: 5410 hours (225 days + 10 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER ST SC SN CL CH DH
  — — — — — — —
  40 51 08 f8 3e 5e 40  Error: UNC 8 sectors at LBA = 0x005e3ef8 = 6176504

  Commands leading to the command that caused the error were:
  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name
  — — — — — — — —  —————-  ——————–
  c8 03 08 f8 3e 5e 40 00      00:01:00.125  READ DMA
  ef 03 46 00 00 00 00 00      00:01:00.063  SET FEATURES [Set transfer mode]
  ef 03 0c 00 00 00 00 00      00:01:00.063  SET FEATURES [Set transfer mode]
  ef 03 00 00 00 00 00 00      00:01:00.063  SET FEATURES [Set transfer mode]
  ec 00 00 00 00 00 00 00      00:01:00.063  IDENTIFY DEVICE

SMART Self-test log structure revision number 1
No self-tests have been logged.  [To run self-tests, use: smartctl -t]


SMART Selective Self-Test Log Data Structure Revision Number (0) should be 1
SMART Selective self-test log data structure revision number 0
Warning: ATA Specification requires selective self-test log data structure revision number = 1
 SPAN  MIN_LBA  MAX_LBA  CURRENT_TEST_STATUS
    1        0        0  Not_testing
    2        0        0  Not_testing
    3        0        0  Not_testing
    4        0        0  Not_testing
    5        0        0  Not_testing
Selective self-test flags (0x0):
  After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.

Leave a Comment »

No comments yet.

RSS feed for comments on this post. TrackBack URI

Leave a Reply

Fill in your details below or click an icon to log in:

WordPress.com Logo

You are commenting using your WordPress.com account. Log Out / Change )

Twitter picture

You are commenting using your Twitter account. Log Out / Change )

Facebook photo

You are commenting using your Facebook account. Log Out / Change )

Google+ photo

You are commenting using your Google+ account. Log Out / Change )

Connecting to %s

%d bloggers like this: